Bidirectional, minimum distance printing Number of characters: Auto cutter problems The auto cutter is jammed. If you are replacing a used ribbon, grasp the end of the tab and remove it from the printer. The sensor has two settings. PS Ripple mVpp or less only when the voltage:

Uploader: Kagagul
Date Added: 11 January 2007
File Size: 67.63 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 21056
Price: Free* [*Free Regsitration Required]

Epson TM-H5000II series Operator’s Manual

Stop printing and contact your dealer or a qualified service person. Notes on slip paper The slip paper must be flat, without curls or wrinkles, especially at the top epson m128c.

To print the manual completely, please, download it. Ribbon Paper roll Hexagonal Switch lock screws cover These screws are used epson m128c for the serial interface They are not always included.

Selectable receive buffer size 45 bytes epson m128c 4K bytes. Page 23 Connecting the N128c Module The display module connector of the printer can be used only for the serial interface. While holding down the FEED button, turn on the printer using the switch on the front of the printer epson m128c begin the self test. Be sure the printed epson m128c side is up, and the sheet is inserted in the right direction. However, using the bookmarks is usually quicker.

Connecting the Cables and Grounding the Printer You can connect up to five epson m128c to the printer. Because of variations in paper roll cores, it is not possible for the sensor to measure exactly the length of paper left on the roll when the sensor is triggered. Epsoj line of dots is missing in the epson m128c. Paper roll epson m128c is poor. Installing or Replacing the Paper Roll Note: Open the printer epsson pulling up on the tab on the front cover.

Form stopper epson m128c MICR head To order ribbon cassettes, contact your dealer or your local affiliate. Page of 70 Go. Turn off the power. Warnings must be followed carefully epson m128c avoid serious bodily injury. If your interface cable requires millimeter-type screws, replace the inch-type screws with the enclosed millimeter-type screws using a hex screwdriver 5 mm.


You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed. Paper dust on the heating element of the thermal print head epson m128c lower the print quality.


Continue to feed slip paper into the printer until the self test prints the following: If there is no paper jam and the printer has been printing for m12c a while, the print head may be overheated. Changing the DIP switch settings If you need to change settings, follow the steps below to make your changes: Epson m128c online documentation for Acrobat Reader is located in the Help directory for Acrobat Reader. Page 41 If there is no paper jam and the printer has been printing for quite a while, the print head may espon overheated.

For a complete listing of topics, see the Contents. Chapter 2 Using the Printer Operating the Control Panels You can control the basic paper feeding operations of the printer with the buttons on the control panels. Paper Specifications Paper Specifications Paper roll single-ply: Epsn the scroll bar next to the bookmarks to find any topic epson m128c want.

Setting Up the Printer page How to epson m128c up the printer. Use the scroll bar on the right side of this screen to move through. Open the front cover. Sheet-roller cleaning-A Part number: New m128d handling enables easy paper roll loading. Epson m128c the paper roll as shown. Ladder bar code printing is possible by using a bar code command. If the print head is overheated, the printer will resume printing when the epson m128c m12c8 cooled usually within two or three minutes.

There is a label on the document table to assist you epson m128c to insert slip paper. Make sure that the power supply cables spson correctly plugged into the printer, the power unit, and to the power outlet. Using this online operator’s guide. Page 6 Seiko Epson Corporation.

Page 56 Normal paper epson m128c