Diagnostic Tips for the Unpack the ribbon cartridge and remove the lock pieces 1. Press LOAD to save your new setting and exit the menu mode. Exiting Hex Dump Mode Turn the printer off, then on again. This utility solved my issue in just 5 minutes and in one click.
|Date Added:||16 September 2018|
|File Size:||23.61 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Manual Gap setting alarm. Data PresentInsert PaperThe printer has received data, but there is no print media loaded inthe selected path. Not Used Valid, Invalid To switch from manual feed oki microline 8480fb continuous forms: Copyright Information, Document Information, Disclaimer, Trademark Information, Regulatory Information The most up-to-date drivers and oki microline 8480fb are available from the web site: Front Feed Continuous Forms 1.
Your printer microlins the following documentation:. Note Printing envelopes requires use of microkine sheet guide 1 insteadof the Auto Align mode.
Page 80 If the cover does not close easily, do not force it. Change to Invalid if you do not wish this value to be stored. Remove paper Remove the jammed paper see page 69 and oki microline 8480fb SEL.
What’s missing? Tell us about it.
Print ModesYour printer has three print modes: Manual Feed single forms fed from theplatform and Front Feed continuousforms. Sets what happens when the printer comes within 1-inch 25 mm of the bottom of the page. Install the Stacker Pull out the sheet supports 1 and move the â€” Minimum Width: Auto AlignThe printer is set at the factory for Auto Align enabled. Remove any bits of paper that come out. Enter text from oki microline 8480fb Lift the oki microline 8480fb lever on the left tractor, then move the left tractor to set thedesired left margin for printing.
If there is a single sheet loaded into the printer, press LOAD to eject it. Open the cover using the grips on either side. Printer Repair Parts, Support and Supplies Printer, oki microline 8480fb, and fax repairs done right the first time.
Note If you are consistently using recycled paper, you need to clean the housing more often because recycled paper generates more paper dust. The right end of the ribbon cartridge is not properly seated oki microline 8480fb the printer.
Oki MICROLINE 8480FB Setup Manual
On-line [the default] or Offline. Head ThermalSingle PassThe printhead has a thermal sensor which has detected that theprinthead is too hot. To microlihe the manual completely, please, download it. Enter text from picture: Turn the platen knob to bring out the continuous forms. Unpack the ribbon cartridge and remove the lock pieces 1. Page 53 Manual feed settings: BuzzerThe default is Enable. Your manual oli to upload Connect the parallel cable to the parallel port on Do not connect both the USB and parallel the printer and secure it with the wire loops.
Page 39 GroupItemSettingsAdjustment cont. Auto Align cannot be used with envelopes. Position the continuous forms stack below oki microline 8480fb printer with no more than about 1 inch 3 cm offset 1. oki microline 8480fb
Set 8480rb setting,press the SEL switch. Change it to Valid if your system uses pin 14of the parallel interface to control automatic line feed.
Fold a single sheet into three thicknesses. The next sheet or form feeds to the selected default Oki microline 8480fb. Swing out the ribbon arms on either end of the cartridge until they snap into place. If you specify that you are using heavy cardstock in most modern printers the machine heats up the fuser more. With just one mivroline you can update the driver as well as the rest of the drivers in your system, such as: Note If you change the print mode while printing, the printer immediately switches to the new print mode.
Utility updated it and the problem disappeared. Sets the pitch to be engaged when the printer control panel is set for 10 oki microline 8480fb and the SI command is received.
OKI MICROLINE FB USER MANUAL Pdf Download.
This sets when the paper ejects, based on the distance betweenthe vertical center of the characters on the last line of the pageand the bottom of the page. Oki microline 8480fb Align When Auto Align is engaged the printer defaultyou can use the front panel switches to change to a different oki microline 8480fb left margin value Align 1, 2, 3, or 4.
Set Pos you have established will be deleted. Pull the ribbon out a bit at the left end of the knob fits, and the guides 2 â€”one at either endâ€” cartridge to give some slack, then slide the ribbon into which the ribbon arms fit. This selection will then automatically appear as the setting for TOF for the corresponding group in oki microline 8480fb Function Setting Menu. Use only genuine OKI replacement ribbons.